|
PLUSH FXÔø‡Ôø‡Ôø‡ Pedals
All Plush pedals feature: Cast aluminum housings, industrial powder coat finish, heat cured silk screen labeling, true bypass, Cliff switch, Neutrik connectors, metal shaft controls, premium boutique quality passive components selected for tone, mil spec fiberglass two sided circuit board construction for consistent long term performance, 5-year warranty. Made in the USA.
See Also [FUCHS Amplifiers]
Good Verbrations Ôø‡. The same innovative reverb circuit in our Verbrator Ôø‡ is now available as a dedicated reverb pedal! Unlike many other reverb pedals, Good Verbrations Ôø‡ allows you to adjust both the level and decay of the reverb signal. You can adjust from a tight short decay, to a long and lush decay, and with total musicality. The reverb circuit is an audiophile grade 16-Khz bandwidth digital circuit. Good Verbrations is extremely low noise, simple to operate, and it can run on guitar or -20-db loop level operation. Like all Plush pedals, Good Verbrations can run on a 9-V battery or a DC adaptor, features an ultra bright bright LED, and features solid cast aluminum power coated enclosure, heat cured silk screening, dual-sided heavy circuit board, premium switches and controls, and premium electronic parts throughout.
Tube FX LoopÔø‡Ôø‡Ôø‡ (NEW!) $329
The Plush Tube FX LoopÔø‡Ôø‡Ôø‡ is the most affordable and flexible all-tube external effects loop on the market! Unlike other Ôø‡Ôø‡Ôø‡tube pedals,Ôø‡Ôø‡Ôø‡ the Tube FX loop Ôø‡ features a power supply with a unique regulated switching technology that takes the incoming 9 volts and converts it up to the optimal 300-Volt high voltage a tube really needs to operate best. In addition, a precision 6-volt DC regulator provides consistent DC power for the tube filament assuring lowest noise and consistent performance despite any changes to incoming line voltage. It can also be used as a tube buffer to convert an incoming high impedance signal to a low impedance for long cable runs or driving a pedal board. The recovery (gain) stage can be used to boost the level of a guitar or pedal board with a true tube audio stage. It provides a warm sweet utility gain stage with a multitude of uses. The Tube FX Pedal Ôø‡ features a unity gain cathode follower to work with any amp that has passive preamp output - power amp input patch jacks, and not a true active effects loop like Ceriatone Ôø‡, Dumble Ôø‡, Bludotone Ôø‡, Brown Note Ôø‡, Quinn Ôø‡, and many other amps. It has a send level control and high headroom. The return portion of the loop features a high impedance input (250-K) and a low output impedance (5-K) with its own level control as well. The loop can be run in series or parallel modes, and features a level adjust switch for rack or pedal style effects. A 9-volt DC adaptor is provided, the Verbrator Ôø‡ features a unique real glass window showing the tube. Like all Fuchs pedals, the Tube FX loop Ôø‡ features solid cast aluminum powder coated enclosure with heat cured silk screening, dual sided heavy circuit boards, premium switches and controls, and premium electronic parts throughout.
[page top]
Crème de la TremÔø‡Ôø‡Ôø‡ $199
In a market filled with so many tremolo pedals, we knew we had to produce something truly unique. The Plush tremolo is designed to emulate the unique sound of the Fender Brownface tremolo, one of the more unique and sought after tremolo tones. Not only does it provide level variation, but the subtle tonal shifts, not unlike a rotating speaker or chorus, unavailable in any other tremolo pedal. Lush, full, spacious and quiet. Simple rate and depth controls allow you to tailor the tone to your exact needs. True hard wire bypass, battery or adaptor power.
[page top]
Extreme CreamÔø‡Ôø‡Ôø‡ $279
When we introduced the Plush CreamÔø‡Ôø‡Ôø‡ a number players became repeat customers. When we asked why, they explained that they set one for a great rhythm crunch, and the second for a screaming lead tone. We went beyond solving that problem in The Extreme CreamÔø‡Ôø‡Ôø‡. We give you two 3-knob channels. One is voiced like the stock Cream. The second is voiced warmer, all under one hood. A simple a/b switch and a simple on/off switch make operation a breeze. In addition to the selected Integrated circuits, we carefully chose each resistor and capacitor to voice the Extreme CreamÔø‡Ôø‡Ôø‡ to be quiet, smooth yet articulate, and dynamic. Both channels respond well to both picking strength and guitar volume, and, best of all, it feels like a tube amp. The gain control takes you from a mild edge to the hardest scream. The tone control takes you from a warm Ôø‡Ôø‡Ôø‡woman toneÔø‡Ôø‡Ôø‡ to a screaming lead tone with just the right amount of sparkle. Choose your tone, then set your level with the output control and rock on!
[page top]
Noxious $249
Designed as a signature pedal for Nick Catanese (Black Label Society, SpeedX),The Noxious pedal brings a whole new definition to the term high gain. Where most pedals end, Noxious is just getting started! The Noxious pedal includes a fully-adjustable input gain control, amp-like fully interactive bass, middle and treble tone controls and a master volume that doesnÔø‡Ôø‡Ôø‡t suck tone. With a low-noise input circuit based on our Pure Gain pedal, and an output section that is like a miniature power amplifier, the Noxious can go from a mild overdrive, to the sound of an amp on the verge of blowing itself to bits! The Noxious features NickÔø‡Ôø‡Ôø‡s custom Ôø‡Ôø‡Ôø‡Evil TwinÔø‡Ôø‡Ôø‡ logo, true-bypass, an ultra bright LED, premium jacks and a solid cast-aluminum shell. Like all Plush Pedals, it's built in the USA from premium parts and has a 5-year warranty.
[page top]
P3 Power SplitterÔø‡Ôø‡Ôø‡ $149
Based on the P3 phantom power technology, the Plush Power SplitterÔø‡Ôø‡Ôø‡ is designed to take the incoming DC power from the P3 Power StationÔø‡Ôø‡Ôø‡ or the incoming power from your P3 equipped amplifier, and distribute it between both P3 and non-P3 pedals. The patented P3 Power technology: http://www.p3dals.com/ is designed to power a pedal board without batteries or extra cables, and operates the pedals via a single audio/power cable. P3 completely does away with the need for batteries, battery cables, "wall-warts," extension cords or power strips. We think it's one of life's "must-have" inventions for guitarists. P3 is available as an upgrade for most pedals, and there's also an external power kit available for use with unmodified pedals. P3 is fully backwards compatible: It will work with and even remotely power non-P3 pedals. P3 does not alter audio circuitry or harm the tone in any way and may in fact improve sound quality and performance as it eliminates battery voltage droop along with the batteries. Several pedal makers and service centers are authorized to perform P3 upgrades to existing pedals, and P3 is being included in some guitar amplifiers. As universally useful and beneficial as P3 is, we expect it will become a standard, becoming to guitar pedals what phantom power is to mixers and microphones. NOTE: The P3 Power SplitterÔø‡Ôø‡Ôø‡ does not power pedals on its own. It requires power to be supplied to it from a P3 power supply or a P3-equipped amplifier to operate. The P3 Power splitter includes a power/audio input as well as four isolated conventional Boss style DC power outputs for conventional pedals. An ultra-bright LED power indicator is provided, which can been seen in direct sunlight. Like all Plush pedals, the P3 Power Supply is made in the USA in a solid cast aluminum powder-coated enclosure, with heat treated silk screening. The power supply includes a 5-year warranty.
[page top]
P3 Power StationÔø‡Ôø‡Ôø‡ $189
Based on the innovative P3 phantom power technology, the Plush P3 Power SupplyÔø‡Ôø‡Ôø‡ is a self-contained DC power supply, which provides 9-VDC of regulated and filtered DC power to up to 1500 ma (1.5 amps) of pedals. The patented P3 Power technology: http://www.p3dals.com/ is designed to power a pedal board without batteries or extra cables, and operates the pedals via a single audio/power cable. P3 completely does away with the need for batteries, battery cables, "wall-warts," extension cords or power strips. We think it's one of life's "must-have" inventions for guitarists. P3 is available as an upgrade for most pedals, and there's also an external power kit available for use with unmodified pedals. P3 is fully backwards compatible: It will work with and even remotely power non-P3 pedals. P3 does not alter audio circuitry or harm the tone in any way and may in fact improve sound quality and performance as it eliminates battery voltage droop along with the batteries. Several pedal makers and service centers are authorized to perform P3 upgrades to existing pedals, and P3 is being included in some guitar amplifiers. As universally useful and beneficial as P3 is, we expect it will become a standard, becoming to guitar pedals what phantom power is to mixers and microphones. The P3 power supply has a standard IEC style power connector, and automatically switches from 100/120 to 220/240 volt AC lines. The P3 Power Supply features two outputs: the P-32 phantom output, as well as a traditional (Boss style) connector, which allows P3 and non-P3 equipped pedals to coexist on a pedal board. Patch cables or the P3 Power Splitter can be used to feed multiple P3 and non-P3 pedals from the power supply outputs. The power supply is self-protected against over current and output shorts, automatically turning off under fault conditions. An ultra-bright LED power indicator is provided, which can been seen in direct sunlight. Like all Plush pedals, the P3 Power Supply is made in the USA in a solid cast aluminum powder-coated enclosure, with heat treated silk screening. The power supply includes a 5-year warranty.
[page top]
Plush CreamÔø‡Ôø‡Ôø‡ $199
The Tube Screamer might be the most popular and famous overdrive pedal ever made. Made popular by SRV and countless others, the TS-808 (and it's derivatives) have become legendary. When we designed the Cream, we sought to produce a pedal with the 3-knob simplicity of this classic pedal, while refining the overall design to modern boutique standards. In addition to the selected Integrated circuit, we carefully chose each resistor and capacitor to voice the Cream to be quiet, smooth yet articulate, and dynamic. It responds well to both picking strength and guitar volume, and, best of all, it feels like a tube amp. The gain control takes you from a mild edge to the hardest scream. The tone control takes you from a warm Ôø‡Ôø‡Ôø‡woman toneÔø‡Ôø‡Ôø‡ to a screaming lead tone with just the right amount of sparkle. Choose your tone, then set your level with the output control and rock on!
[page top]
The Plush DriveÔø‡Ôø‡Ôø‡ $229
Just because you canÔø‡Ôø‡Ôø‡t afford a boutique tube amp, doesnÔø‡Ôø‡Ôø‡t mean you shouldnÔø‡Ôø‡Ôø‡t get the chance to sound like you do! The Plush DriveÔø‡Ôø‡Ôø‡ was designed for those who want the true tone, response and feel of boutique tube amps like the Dumble, Two-Rock or Fuchs, at a reasonable price. Call it your Ôø‡Ôø‡Ôø‡Robben in a boxÔø‡Ôø‡Ôø‡. The unique 4-knob circuit gives you unprecedented control over the most important aspects of your tone. On the input end, the gain and touch controls allow you to set just the right amount of distortion and pick response, based on your guitar and playing style. On the output end, a subtle tone control and level control allow you to set both your overall lead tone and solo level. A unique bi-fet integrated circuit and matched discrete FETs are designed to emulate the smooth overload and musical second order distortion of a tube circuit quietly, musically, and reliably. Coupled to a good clean amp itÔø‡Ôø‡Ôø‡s awesome. Add it to your amps overdrive for a super thick overdrive tone you wonÔø‡Ôø‡Ôø‡t know how you lived without before. Quiet enough to put in front of an overdriven amp easily.
[page top]
Pure GainÔø‡Ôø‡Ôø‡ $179
The name says it all! We started with a "clean sheet of paper approach". A unique circuit topology unlike anything currently on the market, the Pure GainÔø‡Ôø‡Ôø‡ gives up to 25db of gain (thatÔø‡Ôø‡Ôø‡s about a 20 times increase in your guitars output level), with an astoundingly low noise floor. By using selected and matched devices in the circuit, premium parts throughout, we have what we believe may be the quietest gain boost on the market. Besides a true hard-wire passive bypass, the gain control allows you to use Pure GainÔø‡Ôø‡Ôø‡ as an active buffer, which converts your signal from a high impedance input to a low impedance output. Excellent for driving long cables, driving a pedal board, or use it to drive an overdrive pedal or amplifier into searing high gain territory. Excellent for raising single coil pickups to humbucker levels. A small footprint allows easily fitting it into most pedal boards easily.
[page top]
Pure Gain Plus $279
The Pure Gain Plus, combines two of the world's quietest gain boosts with an A/B box. Based on an ingenious suggestion by Dweezil Zappa, the Pure Gain Plus allows you to both balance and boost the levels of two guitars (for example a single coil and a humbucker guitar). It switches to mono operation when only one instrument is plugged-in, allowing it to function as a three mode booster: bypass, and two discrete boost levels.
Like the Pure Gain, when the boost level is at '0' position, the booster acts as a buffer, reducing your guitarÔø‡Ôø‡Ôø‡s impedance to about 20-K, allowing it to drive long cables or additional effects on a pedalboard with minimum sonic impact. Until you've heard the increase in clarity, detail and reduction in noise this impedance change can bring, you havenÔø‡Ôø‡Ôø‡t heard what youÔø‡Ôø‡Ôø‡ve been missing!
9-V battery or DC adaptor powered, the Pure Gain Plus features bright LEDs for each input as well as showing which boost channel is engaged. When the unit is bypassed, the respective LED blinks, and when active it turns solid. Like all Fuchs pedals, the Pure Gain Plus features solid cast aluminum power coated enclosure, heat cured silk screening, dual-sided heavy circuit boards, premium switches and controls, and premium electronic parts throughout.
[page top]
Royal PlushÔø‡Ôø‡Ôø‡ $199
It seems for many years, most guitar compressors have simply been repackaged versions of the same old Dan Armstrong Orange Crush circuit from the '60s! Original Ross and Dan Armstrong compressors are about impossible to find and VERY expensive. While they certainly got the job done, audio circuit design and parts quality has advanced over the years, and there are much better ways to make a compact, great sounding compressor. In additional to using a simple signal path, and audio chips selected for tone, our design uses an actual photocell, just like studio compressors. A unique dual polar power supply means a very wide and distortion-free clean signal swing, no coupling capacitors (and their sonic loses) in the signal path either! The Royal Plush can provide a clean colorless boost, as well as providing a warm smooth compression, free of pumping or unnatural artifacts. True hard wire bypass and premium parts throughout. Volume and bias (compression) controls allow you to set your compression from a soft limiting effect to an extremely compressed output, at unity or boosted levels.
[page top]
The Valve JobÔø‡Ôø‡Ôø‡ $259
Perhaps the closest tone to a boutique tube amp, without the size, weight, and price! Just because you can't afford a boutique tube amp, doesn't mean you shouldnÔø‡Ôø‡Ôø‡t get the chance to sound like you do! The Plush Valve Job was designed for those who want the true tone, response and feel the only a real tube can provide. Like The Plush DriveÔø‡Ôø‡Ôø‡, The Valve JobÔø‡Ôø‡Ôø‡ features a unique 4-knob circuit which gives unprecedented control over the most important aspects of your tone. On the input end, the gain and touch controls allow you to set just the right amount of distortion and pick response, based on your guitar and playing style. On the output end, a subtle tone control and level control allow you to set both your overall lead tone and solo level. A unique bi-fet integrated circuit matched to a real 12AX7 vacuum tube emulates the smooth overload of a tube amp, but with the shimmering harmonics only a tube can provide. Besides a Santana horn-like musical distortion, The Valve JobÔø‡Ôø‡Ôø‡ can provide one of the greatest gnarly slide guitar tones youÔø‡Ôø‡Ôø‡ll ever hear. It has a unique Ôø‡Ôø‡Ôø‡almost out of controlÔø‡Ôø‡Ôø‡ feel that only a real tube can provide.
[page top]
VerbratorÔø‡ $379
The VerbratorÔø‡ is a new multipurpose pedal which combines an all-tube effects loop with a studio grade reverb featuring a 32-Khz clock speed for full 16-K audio bandwidth. The VerbratorÔø‡ is our most innovative pedal offering to date. ItÔø‡Ôø‡Ôø‡s an effects loop, itÔø‡Ôø‡Ôø‡s a reverb, itÔø‡Ôø‡Ôø‡s both!
Unlike other "tube pedals," the VerbratorÔø‡ power supply features a unique regulated switching technology that takes the incoming 9 volts and converts it up to the optimal high voltage a tube really needs to operate best. In addition, a 6-volt DC regulator provides consistent clean DC power for the tube filament assuring lowest noise and consistent performance despite any changes to incoming line voltage.
The VerbratorÔø‡ can be used as a pedal on a pedal board as a reverb pedal. It features a level control and decay control allowing you to have a short medium or long decay reverb algorithm. It can also be used as a tube buffer to convert an incoming high impedance signal to a low impedance for long cable runs or driving a pedal board. The recovery (gain) stage can be used to boost the level of a guitar or pedal board with a true tube audio stage. It provides a warm sweet utility gain stage with a multitude of uses.
The effects loop portion of the pedal features a unity gain cathode follower to work with any amp that has passive preamp output - power amp input patch jacks, and not a true active effects loop like Ceriatone, Dumble, Bludotone, Brown Note, some Marshall models and others. It has a send level control and high headroom. The return portion of the loop features a high impedance input (250-K) and a low output impedance with its own level control as well. The loop can be run in series or parallel modes, and features a level adjust switch for rack or pedal style effects.
9-volt DC adaptor provided, the VerbratorÔø‡ features a unique Ôø‡Ôø‡Ôø‡windowÔø‡Ôø‡Ôø‡ showing the tube. Like all Fuchs pedals, the VerbratorÔø‡ features solid cast aluminum powder coated enclosure with heat cured silk screening, dual sided heavy circuit boards, premium switches and controls, and premium electronic parts throughout.
[page top]
|
